Local

A Pad for a Boat or a Trailer

Around the Chain O'Lakes a lot of driveways carry something on a trailer for half the year. That is a different loading problem from a car, and a driveway built for cars will eventually tell you so.

Living where we do, a fair proportion of the driveways we are asked to look at have a boat on them from October to May. The damage that shows up is consistent enough to be predictable: two depressions where the trailer wheels sit, and one cracked or crushed area where the jack foot goes. It is not bad concrete. It is concrete being asked to do something it was never specified for.

Why a trailer is harder on a slab than a vehicle

Three differences, and they compound.

The load is concentrated. A boat and trailer put a large share of their weight through two wheels and a small jack foot, rather than spreading it across four tyres the way a car does.

It does not move. A car is somewhere else most days. A trailer sits in exactly the same footprint for months, so whatever is happening underneath that spot continues happening uninterrupted. Concrete under sustained load behaves differently from concrete under load that comes and goes.

It is there through the winter. Which is the part people miss. A trailer standing all season holds meltwater and slush against the slab, prevents that patch draining or drying, and keeps road salt carried home on the tyres sitting in one place.

Where the specification should come from

Not from us guessing on a page, and not from a national article either. Two documents hold the real numbers: the plate on the trailer, which carries its rated loaded weight, and the manufacturer's figures for the boat itself.

Those are what a pad should be designed around. Bring them to the visit and the conversation becomes an engineering one rather than a conversation about what usually works. We are not going to publish a thickness here, because the thickness depends entirely on what you are standing on it, and a number invented for the general case is worth nothing in your particular garden.

A panel, not a whole driveway

The practical route in almost every case is a defined thicker panel where the trailer actually stands, with the rest of the driveway at ordinary residential specification.

Two details make that work properly. The panel needs a joint at its boundary, so the slab has a planned line where the depth changes rather than an arbitrary one. And it needs to be big enough for reality: where the trailer sits when it is being manoeuvred in October is not always exactly where it sits in December, and a panel sized to the ideal position rather than the real one puts the wheels on the edge of it.

Measure it with the trailer in place. It takes ten minutes and it is the difference between a panel that works and one that nearly does.

Details worth getting right

  • Spread the jack load. A jack foot concentrates weight into a few square inches. A stand pad, or a substantial piece of timber or steel left permanently under the foot, distributes it for almost no money.
  • Fall away from the standing position. So the patch the trailer occupies is not also the patch water collects in.
  • Think about the turn, not just the stand. Reversing a trailer puts a twisting load into the surface, and the area where that happens takes more punishment than the place it ends up.
  • Keep the approach in mind. A long trailer needs room to swing, and a pad that is perfectly placed but impossible to reverse onto cleanly will be used badly.
  • Move it occasionally. Not a construction point, but the cheapest advice on this page. A trailer shifted a foot or two mid-winter stops the same footprint taking everything.

The seasonal pattern nobody designs for

A boat pad is used in a way almost no other residential concrete is: intensively for a few weeks, then not at all for months, then intensively again.

That matters for two reasons. The first is that the heaviest use of the surface is not the trailer standing still, it is the handful of days each spring and autumn when it is being manoeuvred, reversed, jacked and winched, usually on wet ground, often with a vehicle doing things on the slab it does not normally do.

The second is drying. A surface under a covered boat all winter stays damp long after the rest of the driveway has dried out, and damp concrete in a freeze-thaw climate is concrete working harder than its neighbours. Where the pad can be positioned to get some sun and some airflow rather than tucked against a north wall or under a tree, it will outlast the same slab put somewhere more convenient.

Neither of these shows up in a specification. Both show up in where the pad goes, which is why the siting conversation is worth having before the thickness one.

Before you decide where it goes

One question worth settling early: does the pad reach the road. Anything in the right-of-way brings the Village into the project, with its own requirements and timeline, and a boat pad positioned for convenience can drift closer to that line than you would guess. The permit side is covered in the Antioch driveway permit.

Whether the answer is a panel, a separate pad or a wider driveway gets settled by standing in the garden with the trailer where it lives. That visit is free. The driveway work itself is on concrete driveway, and the reinforcement question that comes up on every heavy-use pad is in is rebar worth it in a driveway.

Sources

  1. Village of Antioch, Building and Code Enforcement - permit requirements for work reaching the right-of-way, and local building enquiries.
  2. Illinois Ready Mixed Concrete Association - homeowner guidance on residential slab construction and loading.

Get a Free Quote

Get your free, on-site quote.

Tell us about your project and we'll call you back the same day to set up a free measure and price.

Get your free quote

Tell us about your project and we will call you back the same day. No obligation.

What are you looking to do?
Roughly how big?
When are you thinking?

Pricing it out is fine. We will not chase you.

What is your ZIP code?

So we can confirm you are in the service area.

Where should we send it?

Free, no-pressure quote · Serving Lake County, IL

By submitting, you agree to our Privacy Policy and Terms, and consent to be contacted by phone, text, or email about your project, including by automated means. Consent isn't a condition of purchase. Msg & data rates may apply.

Tap to Call - (262) 228-5293